Панели не глянцевые, но двигает меня к полировке наличие мелких царапин, гребаный перфекционизм )
Не вздумай браться сошкуривать, много раз пожалеешь, что взялся за это( обратного пути не будет). Попробуй натереть полиролью вдоль полосок фактуры. Тачка станет посвежей выглядеть, царапины остануться, но будут менее заметны на общем фоне блеска.
У нас в городе есть магазин комплектующих, называется Микроника( на подобие Чип и Дип, только цены приемлемые). Позиция: Кнопка JH19-C3 с/ф ON-ON LED12V антивандальная зеленая 12.183(з) Ссылка: -[ссылка]- Кнопка китайская, видел их, всяких модификаций много, на али. Если честно, не уверен сколько долго они продержаться в кофемашине( рассчитаны на 5А). Если не изменяет память, родные переключатели на 15А. И ещё, кнопка размыкает/замыкает только один контакт( а родные переключатели оба- фазу и ноль).
На днях получил от сварщика переднюю панель( заварил торцы, я их успел отшкурить) и боковины с фрезеровки. Крепление боковин планирую сделать на направляющих, с фиксацией хромированными накладками на резьбе. Очень легко в любой момент можно открутить руками и снять без усилий. Работа потихоньку идёт, Mia приобретает привычные глазу черты.
В левом верхнем углу кнопка включения помола без фиксации. Основание будет изготовлено из красного дерева и из него же крышечку для камеры помола. Кажется, красное с чёрным будут приятно сочетаться. Осталось изготовить аккуратный носик и закрепить на выходе. Примерно в таком виде:
Revizor: неугомонный а сам уже одной рукой на двухбойлернике варит это такая миниатюрная MDX? я подумал MCF
Надо ж комплектик для друга подготовить, на замену La Perla с Ascaso mini. Теперь из кофейной секты и не выгонишь, "кулаком по столу" требует с плотными тигровыми крема Ага, корпус прям вокруг двигателя, зазор около 5мм остался.
Кофемашина:Rocket Cellini Evo v2, La Pavoni EL
Кофемолка:Promac MD 74 AT, Mazzer Mini E, Hario mini
Ростер:Gene Cafe, I-Roast2
Др. оборудование: аэропресс, Кемекс, Харио V60, электронная турка, френч-пресс
Кофемашина:Rocket Cellini Evo v2, La Pavoni EL
Кофемолка:Promac MD 74 AT, Mazzer Mini E, Hario mini
Ростер:Gene Cafe, I-Roast2
Др. оборудование: аэропресс, Кемекс, Харио V60, электронная турка, френч-пресс
А что же вот эту площадку не наклонили ? Там всё время много кофе остаётся. Я подумываю спилить её и вставить туда типа что-то трубки, как на фото слева
А что же вот эту площадку не наклонили ? Там всё время много кофе остаётся. Я подумываю спилить её и вставить туда типа что-то трубки, как на фото слева
Наверное, можно с остатками и так попробовать бороться. По мне, проще изготовить носик с "откидываемым верхом" и выметать легко остатки. За счёт статики, и в наклонном носике рано или поздно пыль налипнет, а прочистить парой взмахов уже не получится...
Сыпет в корзинку довольно ровно, к чему пришёл через ряд экспериментов. Осталось сделать из дерева основание и крышечку-затычку на верх молки. Кстати, вот как она выглядит рядом с Танзанией- милашка не правда ли?
Не рассчитывал, что приведение в более-менее приемлемый вид займёт столько времени и сил. Наконец-то, можно сказать, закончил доделки вытерпевшей все мои эксперименты Grimac Mia.
Кому интересно, на установленные антивандальные кнопки не стал накидывать прямое включение помпы + клапана на пролив и клапана на подачу кипятка. Запитал от блока питания подсветку рабочей зоны + индикатор включения и на кнопки установил автомобильные реле 12В по 30А( максимально мощные, по 60руб ). Довольно мягко отщёлкивают, не напрягают и за китайские кнопки нет повода беспокоиться, всё же они по заявленному на 3А рассчитаны.
Стал задумываться о продаже своей Mia, машинка в отличном тех состоянии после переборки...установлена выносная помпа и подводка к канализации. Вдруг кому интересно? Ценник видится в 30к
Стал задумываться о продаже своей Mia, машинка в отличном тех состоянии после переборки...установлена выносная помпа и подводка к канализации. Вдруг кому интересно? Ценник видится в 30к
Фотографию и более подробное описание состояния. Где находится машинка? Выдержит ли до 30 чашек за рабочий день?
Тогда продолжу. Машина в комплектации подключения к водопроводу. Какой фильтр по воде лучше поставить перед машиной? После декальцинации с ножи гриба облезло почти все покрытие это не вредно для здоровья? Посоветуйте сетку для группы и корзину на 2 чашки. Такой размер подойдет?http://www.cafeparts.com/Faema/E61-Group-Head-Filter-Holder-Gasket-Portafilter-%C3%98-74x57x8-Mm/Product/9832 Не пойму как здесь вставить фотографии?
Многие знают, что я фанат Аэропресс. Поэтому, очень долго откладывал в самый дальний ящик покупку данного устройства. Зачем кому-то нужен клон Аэропресса? Однако, на деле оказалось, хоть эти устройства и похожи, у Дельтер Пресса есть свои особенности. Покупать Дельтер Пресс рекомендую в случае, если уже всё есть. На этом можно было бы закончить статью, но давайте разберемся, почему эта кофеварка не только красивый кусок китайского пластика с австралийским акцентом, но имеет огромный потенциал.
Сейчас разгар отпусков и лета 2019 года, я сижу в кофейне, где-то между Австрией, Венгрией и Чехией, пью колд-брю и решил написать для нашего прекрасного русско-язычного кофейного комьюнити, что я думаю по этому поводу и какие основные два метода заваривания доступны для обычного человека. Тем более, что у Sweet Beans Coffee на складе в Краснодаре появился удивительный PUCKPUCK, который теперь всегда со мной.